VoIP Configuration Examples
Short summary:
One POTS dial peer and one VoIP dial peer. Create voip dial-peer 2. dial-peer voice 2 voip ! Create voip dial-peer 1. dial-peer voice 1 voip ! ...
Long summary:
The actual VoIP configuration procedure depends on the topologyof your voice network. The following configuration examples should give you astarting point, but you will need to customize them to reflect your networktopology.
Configuration procedures are supplied for the following scenarios: FXS-to-FXS Connection Using RSVP, page C-1 Linking PBX Users with E&M Trunk Lines, page C-7 FXO Gateway to PSTN, page C-10 FXO Gateway to PSTN (PLAR Mode), page C-12 FXS-to-FXS Connection Using RSVP The following example shows how to configure VoIP for a simple FXS-to-FXSconnection. In this scenario, a very small company with two offices decides to integrate VoIPinto its existing IP network.
One basic telephony device is connected toCatalyst 4224 RLB-1; therefore, Catalyst 4224 RLB-1 is configured for onePOTS dial peer and one VoIP dial peer. Catalyst 4224 RLB-w and Catalyst 4224RLB-e establish the WAN connection between the two offices. Because one POTStelephony device is connected to Catalyst 4224 RLB-2, it is also configured forone POTS dial peer and one VoIP dial peer. In this scenario, only the calling end (Catalyst 4224 RLB-1) is requesting RSVP.
Appendix C VoIP Configuration Examples C-2 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Figure C-1 illustrates the topology of this FXS-to-FXS connection example. Figure C-1 FXS-to-FXS Connection (Example) Catalyst 4224 RLB-1 58515 Dial peer 1 POTS (408) 555-4001 Dial peer 2 POTS (415) 555-3001 64K 64K Voice port 0/0 Voice port0/0 128K Catalyst 4224 RLB-2 Serial port0 Serial port 0 IP cloud V V C-3 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Appendix C VoIP Configuration
Examples Configuration for Catalyst 4224 RLB-1 hostname RLB-1 ! Create voip dial-peer 2 dial-peer voice 2 voip ! Define its associated telephone number and IP address destination-pattern 14155553001 sess-target ipv4:40.0.0.1 ! Request RSVP req-qos controlled-load ! Create pots dial-peer 1 dial-peer voice 1 pots ! Define its associated telephone number and voice port destination-pattern 14085554001 port 0/0 !
Configure serial interface 0 interface Serial0 ip address 10.0.0.1 255.0.0.0 no ip mroute-cache ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 48 48 fair-queue 64 256 36 clockrate 64000 router igrp 888 network 10.0.0.0 network 20.0.0.0 network 40.0.0.0 Appendix C VoIP Configuration Examples C-4 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02
Configuration for Catalyst 4224 RLB-w hostname RLB-w ! Configure serial interface 0 interface Serial0 ip address 10.0.0.2 255.0.0.0 ! Configure RTP header compression ip rtp header-compression ...
Source: www.cisco.com
Related
VoIP Hardware Guide.xls, VoIP Server. Product. Cost. Online.
Asterisk. Free. www.asterisk.org.
Asterisk@Home ... Linux LiveCD VoIP
Server. US$399. www.wifi.com.ar. OpenPBX
...,
more
Zoom Technologies VoIP Hardware Addresses FCC Mandate For 911 Calls, Technologies VoIP Hardware Addresses FCC
Mandate For 911 Calls ... Federal
Communications Commission (FCC) requiring
certain VoIP providers to supply 911 ...,
more
Global VoIP (HSA) v5.cdr, hardware/software. Common stages for
successful VoIP deployments: .... VoIP
Hardware &. Software Forecasts. 7. Winners
& Losers in the ...,
more
