Toyota Matrix 2003 EC Rearview Mirror
Short summary:
Toyota Matrix. Vehicle Protection Blankets, Towels Special Tools Torx head driver T20 Dark Towel or Cloth For Testing Torque Wrench (2) 03.5 N m (030 lbf in) and 014 N m (010 lbf ft) Installation Tools ...
Long summary:
TOYOTA MATRIX 2003 EC REARVIEW MIRROR TOYOTA MATRIX 2003 EC REARVIEW MIRROR Section I Installation Preparation of 13 pages Gentex Document No. 5500229 DIO Rev: A 10/22/01 Part Number: PT37412020 Section I Installation Preparation Kit Contents Item Quantity Reqd. Description 1 1 AD Mirror Assembly w/Compass & Maplights 2 1 Hardware Bag 3 1 Installation Manual Hardware Bag Contents Item Quantity Reqd. Description 1 2 Ttap Connectors: Red 3M 2 1 Wire Cover 3 1 EC Wire Harness 4 6 Foam Tape 5 5 Wire Ties, large 6 12 Wire Ties, small 7 1 Operation Instruction Card Additional Items Required For Installation Item Quantity Reqd. Description Conflicts Note: Recommended Tools Safety Tools Vehicle Protection Blankets, Towels Special Tools Torx head driver T20 Dark Towel or Cloth For Testing Torque Wrench (2) 03.5 N m (030 lbf in) and 014 N m (010 lbf ft) Installation Tools Phillips Screwdriver Ratchet Socket 10mm Needle Nose Pliers Slotted Nylon Removal Tool Blade Screwdriver 4mm max. Utility Knife Special Chemicals 3M TM Prep Solvent 70 General Applicability Note: Recommended Sequence of Application Item Accessory 1 TVIP V3 or V5 2 Audio 3 EC Mirror N1 * Mandatory Legend STOP STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury CRITICAL PROCESS: Proceed with caution to ensure a quality installation. GENERAL PROCESS: This highlights specific processes to ensure a quality installation. TOOLS & EQUIPMENT: This calls out the specific tools and equipment required for this process TOYOTA MATRIX 2003 EC REARVIEW MIRROR Section II Installation Procedure of 13 pages Gentex Document No. 5500229 DIO Rev: A 10/22/01 Section II Installation Procedure A. Vehicle Disassembly 1. Remove the negative Battery Cable. (Fig. A1) i. Protect fender before starting. ii. Be careful; do not touch the positive terminal. 2. Remove OE mirror and discard. (Fig. A2) 3. For sunroof models only. Remove the screw from the overhead dome light assembly bezel. (Fig. A3) 4. For sunroof models only. With a nylon removal tool (NRT), carefully remove the bezel from the overhead dome light assembly. (Fig. A4) i. Store bezel on clean, padded surface. Fig. A4 Nylon Removal Tool Bezel Fig. A1 10mm Socket and Ratchet Negative Battery Cable T20 Torx Head Driver Fig. A2 STOP Fig. A3 Phillips Screwdriver Screw STOP TOYOTA MATRIX 2003 EC REARVIEW MIRROR Section II Installation Procedure of 13 pages Gentex Document No. 5500229 DIO Rev: A 10/22/01 5. For sunroof models only. Remove screw from dome light assembly. (Fig. A5) 6. For sunroof models only. Carefully pull down the dome light assembly to expose the white connector. (Fig. A6) i. Disconnect the connector and store the dome light assembly on a clean, padded surface. 7. Using a slotted NRT, remove both driver and passenger side sun visor clips by rotating clips 90 degrees counter clockwise. (Fig. A7) i. Carefully pull clip away from head ...
Source: www.toyotapart.com
Related
Files under this topic are not filed yet. Please use search bar to find other one
