Red Hat Linux 9 DHCP Server Configuration for Avaya 4600 Series IP ...
Short summary:
how to configure a Red Hat Linux 9 DHCP Server for Avaya 4600 Series IP Telephones. Dynamic Host Configuration Protocol (DHCP) provides a means by which configuration parameters can be automatically assigned to 4600 Series ...
Long summary:
Red Hat Linux 9 DHCP Server Configuration for Avaya 4600 Series IP Telephones Issue 1.0 AM; Reviewed: WCH 3/18/2004 Solution & Interoperability Test Lab Application Notes © 2004 Avaya Inc. All Rights Reserved. 1 of 10 Linux-DHCP.doc Avaya Solution and Interoperability Test Lab Red Hat Linux 9 DHCP Server Configuration for Avaya 4600 Series IP Telephones Issue 1.0 Abstract These Application Notes describe how to configure a Red Hat Linux 9 DHCP Server for Avaya 4600 Series IP Telephones. Dynamic Host Configuration Protocol (DHCP) provides a means by which configuration parameters can be automatically assigned to 4600 Series IP Telephones on a TCP/IP network, thus removing the need to individually assign and maintain IP addresses and other parameters for each IP telephone on the network. These Application Notes were written at the request of the Avaya Hosted Solutions team. AM; Reviewed: WCH 3/18/2004 Solution & Interoperability Test Lab Application Notes © 2004 Avaya Inc. All Rights Reserved. 2 of 10 Linux-DHCP.doc 1. Introduction These Application Notes describe how to configure a Red Hat Linux 9 DHCP Server for Avaya 4600 Series IP Telephones. DHCP is a network protocol that provides a means by which configuration parameters can be automatically assigned to 4600 Series IP Telephones on a TCP/IP network, thus removing the need to individually assign and maintain IP addresses and other parameters for each IP Telephone on the network. The sample configuration depicted in Figure 1 uses separate Virtual Local Area Networks (VLANs) for voice and data traffic. As a result, the DHCP configuration presented in these Application Notes supports scenarios where the switch ports may connect to a computer, an IP telephone, or an IP telephone with an attached computer. IEEE 802.1Q tagged VLAN ID 120 was used for the IP telephones, and untagged VLAN ID 130 was used for computers, whether standalone, or attached to an IP Telephone. Figure 1: Red Hat Linux DHCP Server Avaya IP Telephone Configuration AM; Reviewed: WCH 3/18/2004 Solution & Interoperability Test Lab Application Notes © 2004 Avaya Inc. All Rights Reserved. 3 of 10 Linux-DHCP.doc The following DHCP server parameters were configured for the endpoints on the native data VLAN: Data endpoints IP address Range (178.16.13.100 178.16.13.250) Router IP address (178.16.13.1) Subnet broadcast IP address (178.16.13.255) Subnet Mask (255.255.255.0) L2Q=1 IEEE 802.1Q trunking L2QVLAN=120 Voice VLAN The following DHCP server parameters were configured for the Avaya 4600 Series IP Telephones on the voice VLAN: Telephone IP address Range (178.16.12.100 178.16.12.250) Router IP address (178.16.12.1) Subnet broadcast IP address (178.16.12.255) Subnet Mask (255.255.255.0) IP address of C-LAN board MCIPADD (178.16.12.21) Gatekeeper port MCPORT (Default: 1719) TFTP server IP address TFTPSRVR (178.16.12.100) The following occurs when an IP telephone is installed (or reset). The IP telephone will initially sen ...
Source: www.avaya.com
Related
Hacking The Linux Kernel, Unreliable Guide To Hacking The Linux
Kernel.the common routines and general
requirements for kernel code: its goal is
to serve as a primer for Linux kernel
development for experienced C
programmers...,
more
Linux Secure and Optimized Server, Linux Secure and Optimized Server. A guide
for information system, configuration,
optimization and ... fonts to other X
servers remotely with this package, ...,
more
Linux Terminal Server Project: Server Configuration Guidelines, Linux Terminal Server Project: Server
Configuration Guidelines. locate XDM
servers. Once an XDM server is located,
the XDM server. LTSP Architecture The
principal goal of sizing LTSP servers ...,
more
