Assemble Rear Mounting Bracket Assembly
Short summary:
Dodge Ram Quad Cab Pickup. 2002 - 2005. Part Number: 75101-01 Wrap the splice area with electrical tape. Wiring. 2004 2006 Vehicles. Wiring ...
Long summary:
Installation Instructions Installation Instructions INSTALLATION TIME SKILL LEVEL 3 Hours 4 Dif cult TOOLS Vehicle Application 1/8 Drill Bits Dodge Ram Quad Cab Pickup 2002 2005 Part Number: 75101-01 Automatic Retracting Running Board 13 mm 1/8 and 3/16 Dodge Ram Mega Cab Pickup 2006 Current Part Number: 75118-01 www.Bestop.com Were here to help! Visit our web site and click on Ask a Question . Click here for more Truck Accessories by Bestop. Power Step Installation Instructions Rev. D 0506 75101 / 75118 pg. 2 Parts List and Hardware Identi cation Large Hex Bolt, Qty 8 Note: Bolts preinstalled in Mounting Brackets. Rivet, Qty 8 Small Hex Bolt, Qty 1 Washer, Qty 1 Medium Hex Bolt, Qty 4 Control Box, 404.41 Qty 1 Control Box Mounting Clip, Qty 1 Front Mounting Bracket, 404.30 Qty 2 Front Arm, 404.27 Qty 2 Rear Mounting Bracket Drivers Side, 404.31 Qty 1 Step, 404.20 Qty 2 Socket Head Bolt, Qty 8 Rear Mounting Bracket Passengers Side, 404.32 Qty 1 Wiring Harness, 404.29 Qty 1 Wire Ties, Qty 25 Rear Arm, 404.28 Qty 2 Mounting Bracket Support Nut, Qty 4 Power Step Installation Instructions Rev. D 0506 75101 / 75118 pg. 3 Make sure that the two tabs in the bracket rest on the edge of the hole in the sheet metal. Locate the Rear Mounting Brackets and the Mounting Bracket Support Nuts in the parts kit. Use a Medium Hex Bolt to attach a Support Nut to the back of the Rear Mounting Bracket. If you have a Mega Cab, remove the tape and cut as indicated for the Mega Cab Rear Bracket, if necessary. Counting from the front, locate the third (3rd) and seventh (7th) plugs on the inner sill for a Quad Cab. For a Mega Cab locate the third (3rd) and eighth (8th) plugs. Use a at screwdriver to pry them out. View from under vehicle Front Rear Remove 3rd Plug Remove 7th Plug for Quad Cab Drivers Side Rear Mounting Bracket Mounting Bracket Support Nut Medium Hex Bolt Frame Drivers Side Drivers Side Remove Plugs Drivers Side Assemble Rear Mounting Bracket Assembly Drivers Side Slide the Support Nut on the Rear Mounting Bracket Assembly into the rear hole where the plug was removed. Hook the tabs on the bracket over the edge of the hole to help secure the bracket to the frame. Pull back on the Hex Bolt to snug the nut and bracket up to each other and use a 13mm wrench to tighten the bolt to 16 ft./lbs. (22 Nm). Rear Mounting Bracket Mounting Bracket Support Nut behind frame Medium Hex Bolt Tighten to 16 ft./lbs. Frame Drivers Side Install Rear Mounting Bracket Assembly Drivers Side Use the two small holes in the Rear Mounting Bracket as templates to drill two 1/8 holes. Paint the edges of the holes with Corrosion Protection Paint to prevent rust. Install a Rivet in each hole. Use a 1/8 Allen Wrench to tighten the set screw on the bracket to 1.5 ft./lbs. (2 Nm). Repeat Steps 1-4 with the Front Mounting Bracket. Make sure the bracket is ush with the inner sill before riveting. Drill 1/8 holes, seal and install Rivets Tighten Set Screw to 1.5 ft./lbs (2 Nm) Drivers ...
Source: www.bestoppowerstep.com
Search Terms:
Related
2006 Dodge Charger/Magnum Police Upfitter's Guide, 2006 Dodge Charger and Magnum Service
Manual for appropriate service procedures,
torques specications, component separation
clearances, and other standard information
that is common with the unmodied vehicle
...,
more
BD X-MONITOR DODGE Installation Manual, thermocouple lead to the male connector of
the thermocouple. Route the large yellow
covered wire toward the firewall taking
precaution to keep it away ...,
more
RAM 3500 CHASSIS CAB, NOISE PASS BY STANDARDS. HEAVY DUTY ENGINE
CERTIFICATION. SAFETY ... ELECTRICAL /
WIRING INFORMATION. OPTIONAL EQUIPMENT
WEIGHTS. OCCUPANT RESTRAINT SYSTEM ...,
more
